200-125 Exam
Secrets to ccna 200 125 book
It is more faster and easier to pass the Cisco 200 125 ccna exam by using Verified Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) questuins and answers. Immediate access to the Up to the minute ccna 200 125 study guide Exam and find the same core area ccna 200 125 ebook questions with professionally verified answers, then PASS your exam with a high score now.
Q141. - (Topic 8)
Which routing protocol has the smallest default administrative distance?
A. IBGP
B. OSPF
C. IS-IS
D. EIGRP
E. RIP
Answer: D
Explanation: http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/15986-admin-distance.html
Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports:
Route Source
Default Distance Values
Connected interface 0
Static route 1
Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5
External Border Gateway Protocol (BGP) 20
Internal EIGRP 90
IGRP 100 OSPF 110
Intermediate System-to-Intermediate System (IS-IS) 115
Routing Information Protocol (RIP) 120
Exterior Gateway Protocol (EGP) 140
On Demand Routing (ODR) 160
External EIGRP 170
Internal BGP 200
Unknown* 255
Q142. - (Topic 4)
What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)
A. They create split-horizon issues.
B. They require a unique subnet within a routing domain.
C. They emulate leased lines.
D. They are ideal for full-mesh topologies.
E. They require the use of NBMA options when using OSPF.
Answer: B,C
Explanation:
Subinterfaces are used for point to point frame relay connections, emulating virtual point to point leased lines. Each subinterface requires a unique IP address/subnet. Remember, you cannot assign multiple interfaces in a router that belong to the same IP subnet.
Topic 5, Infrastructure Services
190. - (Topic 5)
What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72?
A. B514 : 82C3 : 0029 : EC7A : EC72
B. B514 : 82C3 :: 0029 : EC7A : EC72
C. B514 : 82C3 : 0029 :: EC7A : 0000 : EC72
D. B514 : 82C3 :: 0029 : EC7A : 0 : EC72
Answer: D
Explanation:
There are two ways that an IPv6 address can be additionally compressed: compressing leading zeros and substituting a group of consecutive zeros with a single double colon (::). Both of these can be used in any number of combinations to notate the same address. It is important to note that the double colon (::) can only be used once within a single IPv6 address notation. So, the extra 0’s can only be compressed once.
Q143. - (Topic 5)
What is the default Syslog facility level?
A. local4
B. local5
C. local6
D. local7
Answer: D
Explanation:
By default, Cisco IOS devices, CatOS switches, and VPN 3000 Concentrators use facility local7 while Cisco PIX Firewalls use local4 to send syslog messages. Moreover, most Cisco devices provide options to change the facility level from their default value.
Reference: http://www.ciscopress.com/articles/article.asp?p=426638
Q144. - (Topic 7)
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Answer: A
Explanation:
Flow monitors are the Flexible NetFlow component that is applied to interfaces to perform network traffic monitoring. Flow monitors consist of a record and a cache. You add the record to the flow monitor after you create the flow monitor. The flow monitor cache is automatically created at the time the flow monitor is applied to the first interface. Flow data
is collected from the network traffic during the monitoring process based on the key and nonkey fields in the record, which is configured for the flow monitor and stored in the flow monitor cache.
For example, the following example creates a flow monitor named FLOW-MONITOR-1 and enters Flexible NetFlow flow monitor configuration mode:
Router(config)# flow monitor FLOW-MONITOR-1 Router(config-flow-monitor)#
Q145. - (Topic 8)
What is the best way to verify that a host has a path to other hosts in different networks?
A. Ping the loopback address.
B. Ping the default gateway.
C. Ping the local interface address.
D. Ping the remote network.
Answer: D
Explanation:
Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, the ping command is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.
If you call ipconfig /all and receive a response, there is no need to ping the loopback address and your own IP address — Ipconfig has already done so in order to generate the report.
It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:
ping < IP address >
Perform the following steps when using Ping:
✑ Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.
ping 127.0.0.1
If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.
✑ Ping the IP address of the local computer to verify that it was added to the network
correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.
ping < IP address of local host >
✑ Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.
ping < IP address of default gateway >
✑ Ping the IP address of a remote host to verify that you can communicate through a router.
ping < IP address of remote host >
✑ Ping the host name of a remote host to verify that you can resolve a remote host name.
ping < Host name of remote host >
✑ Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.
pathping < IP address of remote host >
Q146. - (Topic 3)
Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network. The network administrator connected to router Coffee via the console port, issued the show ip route command, and was able to ping the server.
Based on the output of the show ip route command and the topology shown in the graphic, what is the cause of the failure?
A. The network has not fully converged.
B. IP routing is not enabled.
C. A static route is configured incorrectly.
D. The FastEthernet interface on Coffee is disabled.
E. The neighbor relationship table is not correctly updated.
F. The routing table on Coffee has not updated.
Answer: C
Explanation:
The default route or the static route was configured with incorrect next-hop ip address 172.19.22.2. The correct IP address will be 172.18.22.2 to reach server located on 172.31.5.0 network. IP route 0.0.0.0 0.0.0.0 172.18.22.2
Q147. - (Topic 7)
What are three reasons to collect Netflow data on a company network? (Choose three.)
A. To identify applications causing congestion.
B. To authorize user network access.
C. To report and alert link up / down instances.
D. To diagnose slow network performance, bandwidth hogs, and bandwidth utilization.
E. To detect suboptimal routing in the network.
F. To confirm the appropriate amount of bandwidth that has been allocated to each Class of Service.
Answer: A,D,F
Explanation:
NetFlow facilitates solutions to many common problems encountered by IT professionals.
+ Analyze new applications and their network impact
Identify new application network loads such as VoIP or remote site additions.
+ Reduction in peak WAN traffic
Use NetFlow statistics to measure WAN traffic improvement from application-policy changes; understand who is utilizing the network and the network top talkers.
+ Troubleshooting and understanding network pain points
Diagnose slow network performance, bandwidth hogs and bandwidth utilization quickly with command line interface or reporting tools. -> D is correct.
+ Detection of unauthorized WAN traffic
Avoid costly upgrades by identifying the applications causing congestion. -> A is correct.
+ Security and anomaly detection
NetFlow can be used for anomaly detection and worm diagnosis along with applications such as Cisco CS-Mars.
+ Validation of QoS parameters
Confirm that appropriate bandwidth has been allocated to each Class of Service (CoS) and that no CoS is over- or under-subscribed.-> F is correct.
Q148. - (Topic 8)
Which VTP mode prevents you from making changes to VLANs?
A. server
B. off
C. client
D. transparent
Answer: C
Q149. CORRECT TEXT - (Topic 7)
A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.
The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.
All passwords have been temporarily set to "cisco".
The Core connection uses an IP address of 198.18.247.65
The computers in the Hosts LAN have been assigned addresses of 192.168.240.1 - 192.168.240.254
✑ host A 192.168.240.1
✑ host B 192.168.240.2
✑ host C 192.168.240.3
Answer:
Corp1#conf t
Corp1(config)# access-list 128 permit tcp host 192.168.240.1 host 172.22.141.26 eq www Corp1(config)# access-list 128 deny tcp any host 172.22.141.26 eq www
Corp1(config)# access-list 128 permit ip any any Corp1(config)#int fa0/1
Corp1(config-if)#ip access-group 128 out Corp1(config-if)#end
Corp1#copy run startup-config
Q150. - (Topic 8)
A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?
A. the EIGRP route
B. the OSPF route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Answer: A