200-125 Exam
Amazing ccna 200 125 dumps secrets
Your success in Cisco ccna 200 125 pdf is our sole target and we develop all our ccna routing and switching 200 125 official cert guide library braindumps in a way that facilitates the attainment of this target. Not only is our 200 125 ccna study material the best you can find, it is also the most detailed and the most updated. ccna 200 125 book Practice Exams for Cisco CCNA Routing and Switching 125 200 are written to the highest standards of technical accuracy.
Q111. - (Topic 8)
Which command can you enter to set the default route for all traffic to an interface?
A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
C. router(config-router)#default-information originate
D. router(config-router)#default-information originate always
Answer: A
Q112. - (Topic 5)
When a DHCP server is configured, which two IP addresses should never be assignable to
hosts? (Choose two.)
A. network or subnetwork IP address
B. broadcast address on the network
C. IP address leased to the LAN
D. IP address used by the interfaces
E. manually assigned address to the clients
F. designated IP address to the DHCP server
Answer: A,B
Explanation:
Network or subnetwork IP address (for example 11.0.0.0/8 or 13.1.0.0/16) and broadcast address (for example 23.2.1.255/24) should never be assignable to hosts. When try to assign these addresses to hosts, you will receive an error message saying that they can’t be assignable.
Q113. - (Topic 7)
What are three factors a network administrator must consider before implementing Netflow
in the network? (Choose three.)
A. CPU utilization
B. where Netflow data will be sent
C. number of devices exporting Netflow data
D. port availability
E. SNMP version
F. WAN encapsulation
Answer: A,B,C
Explanation:
NetFlow has a reputation for increasing CPU utilization on your network devices. Cisco's performance testing seems to indicate that newer hardware can accommodate this load pretty well, but you will still want to check it out before you turn on the feature. Some symptoms of high CPU utilization are very large jitter and increased delay. Services running on the device may also be affected.
Another thing to keep in mind is the amount of data you're going to be sending across the network. Depending on how much traffic you have and how you configure it, the traffic can be substantial. For example, you may not want to send NetFlow data from a datacenter switch to a NetFlow collector on the other side of a small WAN circuit. Also bear in mind that the flows from aggregating large numbers of devices can add up.
Reference: http://searchenterprisewan.techtarget.com/tip/How-the-NetFlow-protocol- monitors-your-WAN
Q114. - (Topic 3)
Why do large OSPF networks use a hierarchical design? (Choose three.)
A. to decrease latency by increasing bandwidth
B. to reduce routing overhead
C. to speed up convergence
D. to confine network instability to single areas of the network
E. to reduce the complexity of router configuration
F. to lower costs by replacing routers with distribution layer switches
Answer: B,C,D
Explanation:
OSPF implements a two-tier hierarchical routing model that uses a core or backbone tier known as area zero (0). Attached to that backbone via area border routers (ABRs) are a number of secondary tier areas. The hierarchical approach is used to achieve the following:
•Rapid convergence because of link and/or switch failures
•Deterministic traffic recovery
•Scalable and manageable routing hierarchy, reduced routing overhead.
Q115. - (Topic 4)
At which layer of the OSI model does PPP perform?
A. Layer 2
B. Layer 3
C. Layer 4
D. Layer 5
Answer: A
Explanation:
The Point-to-Point Protocol (PPP) provides a standard method for transporting multi- protocol datagrams over point-to-point links. PPP was originally emerged as an encapsulation protocol for transporting IP traffic between two peers. It is a data link layer protocol (layer 2 in the OSI model)
Q116. - (Topic 5)
Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor
Answer: C
Explanation:
To enable IPv6 routing on the Cisco router use the following command: ipv6 unicast-routing
If this command is not recognized, your version of IOS does not support IPv6.
Q117. - (Topic 3)
Refer to the exhibit.
Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown?
A. One interface has a problem.
B. Two interfaces have problems.
C. The interfaces are functioning correctly.
D. The operational status of the interfaces cannot be determined from the output shown.
Answer: C
Explanation:
The output shown shows normal operational status of the router’s interfaces. Serial0/0 is down because it has been disabled using the “shutdown” command.
Q118. - (Topic 8)
when you troubleshoot an IPv4 connectivity issue on a router, which three router configuration checks you must perform?
A. Verify that the router interface IP address IP address is correct.
B. Verify that the DNS is configured correctly.
C. Verify that the router and the host use the same subnet mask.
D. Verify that the router firmware is up-to-date.
E. Verify that a default route is configured.
F. Verify that the route appears in the routing table
Answer: A,B,F
Q119. - (Topic 3)
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
Answer: B,D
Explanation:
Here is a list of the differences between OSPFv2 and OSPFv3:
✑ They use different address families (OSPFv2 is for IPv4-only, OSPFv3 can be used for IPv6-only or both protocols
✑ OSPFv3 introduces new LSA types
✑ OSPFv3 has different packet format
✑ OSPFv3 uses different flooding scope bits (U/S2/S1)
✑ OSPFv3 adjacencies are formed over link-local IPv6 communications
✑ OSPFv3 runs per-link rather than per-subnet
✑ OSPFv3 supports multiple instances on a single link, Interfaces can have multiple IPv6 addresses
✑ OSPFv3 uses multicast addresses FF02::5 (all OSPF routers), FF02::6 (all OSPF DRs)
✑ OSPFv3 Neighbor Authentication done with IPsec (AH)
✑ OSPFv2 Router ID (RID) must be manually configured, still a 32-bit number
Reference: http://www.networkworld.com/article/2225270/cisco-subnet/ospfv3-for-ipv4-and- ipv6.html
Q120. - (Topic 8)
Which network topology allows all traffic to flow through a central hub?
A. bus
B. star
C. mesh
D. ring
Answer: B