200-125 Exam
ccna 200 125 ebook? Tips for success
We provide real ccna routing and switching 200 125 exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco cisco ccna 200 125 Exam quickly & easily. The 125 200 PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco 200 125 ccna dumps pdf and vce product and material, you can easily pass the ccna 200 125 book exam.
Q101. - (Topic 8)
Which command can you enter to troubleshoot the failure of address assignments?
A. show ip dhcp pool
B. show ip dhcp database
C. show ip dhcp import
D. clear ip dhcp server statistics
Answer: A
Q102. - (Topic 8)
Refer to the exhibit.
What is the result of setting the no login command?
A. Telnet access is denied.
B. Telnet access requires a new password at the first login.
C. Telnet access requires a new password.
D. no password is required for telnet access.
Answer: D
Q103. - (Topic 7)
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.
Answer: C
Explanation:
The “show ip ospf interface command on R3 and R5 shows that the hello and dead intervals do not match. They are 50 and 200 on R3 and 10 and 40 on R5.
Q104. - (Topic 3)
Refer to the exhibit.
For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.)
A. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server.
B. Router1 is acting as a TFTP server for other routers.
C. Router1 cannot locate a valid IOS image in flash memory.
D. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
E. Cisco routers will first attempt to load an image from TFTP for management purposes.
Answer: A,C
Explanation:
The loading sequence of CISCO IOS is as follows: Booting up the router and locating the Cisco IOS
1. POST (power on self-test)
2. Bootstrap code executed
3. Check Configuration Register value (NVRAM) which can be modified using the config- register command
0 = ROM Monitor mode 1 = ROM IOS
2 - 15 = startup-config in NVRAM
4. Startup-config filE. Check for boot system commands (NVRAM)
If boot system commands in startup-config
a. Run boot system commands in order they appear in startup-config to locate the IOS
b. [If boot system commands fail, use default fallback sequence to locate the IOS (Flash, TFTP, ROM)?]
If no boot system commands in startup-config use the default fallback sequence in locating the IOS:
a. Flash (sequential)
b. TFTP server (netboot)
c. ROM (partial IOS) or keep retrying TFTP depending upon router model
5. If IOS is loaded, but there is no startup-config file, the router will use the default fallback sequence for locating the IOS and then it will enter setup mode or the setup dialogue.
Q105. - (Topic 4)
Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link?
A. show frame-relay lmi
B. show frame-relay map
C. show frame-relay pvc
D. show interfaces serial
Answer: B
Explanation:
When connecting Cisco devices with non-Cisco devices, you must use IETF4 encapsulation on both devices. Check the encapsulation type on the Cisco device with the show frame-relay map exec command.
Q106. - (Topic 5)
Refer to the exhibit.
In this VLSM addressing scheme, what summary address would be sent from router A?
A. 172.16.0.0 /16
B. 172.16.0.0 /20
C. 172.16.0.0 /24
D. 172.32.0.0 /16
E. 172.32.0.0 /17
F. 172.64.0.0 /16
Answer: A
Explanation:
Router A receives 3 subnets: 172.16.64.0/18, 172.16.32.0/24 and 172.16.128.0/18.
All these 3 subnets have the same form of 172.16.x.x so our summarized subnet must be also in that form -> Only A, B or .
The smallest subnet mask of these 3 subnets is /18 so our summarized subnet must also have its subnet mask equal or smaller than /18.
-> Only answer A has these 2 conditions ->.
Q107. - (Topic 3)
Which command is used to display the collection of OSPF link states?
A. show ip ospf link-state
B. show ip ospf lsa database
C. show ip ospf neighbors
D. show ip ospf database
Answer: D
Explanation:
The “show ip ospf database” command displays the link states. Here is an example: Here is the lsa database on R2.
R2#show ip ospf database
OSPF Router with ID (2.2.2.2) (Process ID 1) Router Link States (Area 0)
Link ID ADV Router Age Seq# Checksum Link count 2.2.2.2 2.2.2.2 793 0x80000003 0x004F85 2
10.4.4.4 10.4.4.4 776 0x80000004 0x005643 1
111.111.111.111 111.111.111.111 755 0x80000005 0x0059CA 2
133.133.133.133 133.133.133.133 775 0x80000005 0x00B5B1 2
Net Link States (Area 0)
Link ID ADV Router Age Seq# Checksum
10.1.1.1 111.111.111.111 794 0x80000001 0x001E8B
10.2.2.3 133.133.133.133 812 0x80000001 0x004BA9
10.4.4.1 111.111.111.111 755 0x80000001 0x007F16
10.4.4.3 133.133.133.133 775 0x80000001 0x00C31F
Q108. - (Topic 4)
Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?
A. RSA
B. L2TP
C. IPsec
D. PPTP
Answer: C
Explanation:
IPSec is a framework of open standards that provides data confidentiality, data integrity, and data authentication between participating peers at the IP layer. IPSec can be used to protect one or more data flows between IPSec peers.
Q109. - (Topic 5)
Which IPv6 address is valid?
A. 2001:0db8:0000:130F:0000:0000:08GC:140B
B. 2001:0db8:0:130H::87C:140B
C. 2031::130F::9C0:876A:130B
D. 2031:0:130F::9C0:876A:130B
Answer: D
Explanation:
An IPv6 address is represented as eight groups of four hexadecimal digits, each group
representing 16 bits (two octets). The groups are separated by colons (:). An example of an IPv6 address is 2001:0db8:85a3:0000:0000:8a2e:0370:7334. The leading 0’s in a group can be collapsed using ::, but this can only be done once in an IP address.
Topic 6, Infrastructure Security
261. - (Topic 6)
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
Answer: C
Explanation:
This question is to examine the layer 2 security configuration.
In order to satisfy the requirements of this question, you should perform the following configurations in the interface mode:
First, configure the interface mode as the access mode
Second, enable the port security and set the maximum number of connections to 1.
Q110. - (Topic 4)
Refer to the exhibit.
What is the meaning of the term dynamic as displayed in the output of the show frame- relay map command shown?
A. The Serial0/0 interface is passing traffic.
B. The DLCI 100 was dynamically allocated by the router.
C. The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server.
D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud.
E. The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP.
Answer: E
Explanation:
Inverse Address Resolution Protocol (Inverse ARP) was developed to provide a mechanism for dynamic DLCI to Layer 3 address maps. Inverse ARP works much the same way Address Resolution Protocol (ARP) works on a LAN. However, with ARP, the device knows the Layer 3 IP address and needs to know the remote data link MAC address. With Inverse ARP, the router knows the Layer 2 address which is the DLCI, but needs to know the remote Layer 3 IP address.
When using dynamic address mapping, Inverse ARP requests a next-hop protocol address for each active PVC. Once the requesting router receives an Inverse ARP response, it updates its DLCI-to-Layer 3 address mapping table. Dynamic address mapping is enabled by default for all protocols enabled on a physical interface. If the Frame Relay environment supports LMI autosensing and Inverse ARP, dynamic address mapping takes place automatically. Therefore, no static address mapping is required.