200-125 Exam
Jan 2021 updated: ccna routing and switching 200 125
It is impossible to pass Cisco 200 125 ccna exam without any help in the short term. Come to Actualtests soon and find the most advanced, correct and guaranteed Cisco ccna routing and switching 200 125 official cert guide library practice questions. You will get a surprising result by our Rebirth CCNA Cisco Certified Network Associate CCNA (v3.0) practice guides.
Q21. - (Topic 5)
Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)
A. Network A - 172.16.3.48/26
B. Network A - 172.16.3.128/25
C. Network A - 172.16.3.192/26
D. Link A - 172.16.3.0/30
E. Link A - 172.16.3.40/30
F. Link A - 172.16.3.112/30
Answer: B,D
Explanation:
Only a /30 is needed for the point to point link and sine the use of the ip subnet-zero was used, 172.16.3.0/30 is valid. Also, a /25 is required for 120 hosts and again 172.16.3.128/25 is the best, valid option.
Q22. - (Topic 5)
Refer to the exhibit.
Which rule does the DHCP server use when there is an IP address conflict?
A. The address is removed from the pool until the conflict is resolved.
B. The address remains in the pool until the conflict is resolved.
C. Only the IP detected by Gratuitous ARP is removed from the pool.
D. Only the IP detected by Ping is removed from the pool.
E. The IP will be shown, even after the conflict is resolved.
Answer: A
Explanation:
An address conflict occurs when two hosts use the same IP address. During address assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is detected, the address is removed from the pool. The address will not be assigned until the administrator resolves the conflict.
(Reference: http://www.cisco.com/en/US/docs/ios/12_1/iproute/configuration/guide/1cddhcp.html)
Q23. - (Topic 5)
A network engineer wants to allow a temporary entry for a remote user with a specific username and password so that the user can access the entire network over the Internet.
Which ACL can be used?
A. standard
B. extended
C. dynamic
D. reflexive
Answer: C
Explanation:
We can use a dynamic access list to authenticate a remote user with a specific username and password. The authentication process is done by the router or a central access server such as a TACACS+ or RADIUS server. The configuration of dynamic ACL can be read here: http://www.cisco.com/en/US/tech/tk583/tk822/technologies_tech_note09186a0080094524. shtml
Q24. - (Topic 6)
Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?
A. BackboneFast
B. UplinkFast
C. Root Guard
D. BPDU Guard
E. BPDU Filter
Answer: D
Explanation:
We only enable PortFast feature on access ports (ports connected to end stations). But if someone does not know he can accidentally plug that port to another switch and a loop may occur when BPDUs are being transmitted and received on these ports.
With BPDU Guard, when a PortFast receives a BPDU, it will be shut down to prevent a loop.
Q25. - (Topic 5)
Which three statements about HSRP operation are true? (Choose three.)
A. The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
B. The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
C. HSRP supports only clear-text authentication.
D. The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.
E. The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.
F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.
Answer: A,B,F
Explanation:
The virtual MAC address of HSRP version 1 is 0000.0C07.ACxx, where xx is the HSRP group number in hexadecimal based on the respective interface. For example, HSRP group 10 uses the HSRP virtual MAC address of 0000.0C07.AC0A. HSRP version 2 uses a virtual MAC address of 0000.0C9F.FXXX (XXX: HSRP group in hexadecimal).
Q26. - (Topic 8)
Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE
Answer: B
Q27. - (Topic 7)
Refer to the exhibit.
Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)
A. The cable that is connected to S0/0 on RouterA is faulty.
B. Interface S0/0 on RouterB is administratively down.
C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.
Answer: E,F
Explanation:
From the output we can see that there is a problem with the Serial 0/0 interface. It is enabled, but the line protocol is down. There could be a result of mismatched encapsulation or the interface not receiving a clock signal from the CSU/DSU.
Q28. - (Topic 3)
Refer to the exhibit.
When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?
A. AS numbers must be changed to match on all the routers
B. Loopback interfaces must be configured so a DR is elected
C. The no auto-summary command is needed on Router A and Router C
D. Router B needs to have two network statements, one for each connected network
Answer: A
Explanation:
This question is to examine the understanding of the interaction between EIGRP routers. The following information must be matched so as to create neighborhood.
EIGRP routers to establish, must match the following information:
1. AS Number;
2. K value.
Q29. - (Topic 8)
Which command can you enter to determine whether a switch is operating in trunking mode?
A. show ip interface brief
B. show vlan
C. show interfaces
D. show interface switchport
Answer: D
Q30. - (Topic 7)
What command visualizes the general NetFlow data on the command line?
A. show ip flow export
B. show ip flow top-talkers
C. show ip cache flow
D. show mls sampling
E. show mls netflow ip
Answer: C
Explanation:
The following is an example of how to visualize the NetFlow data using the CLI. There are three methods to visualize the data depending on the version of Cisco IOS Software. The traditional show command for NetFlow is "show ip cache flow" also available are two forms of top talker commands. One of the top talkers commands uses a static configuration to view top talkers in the network and another command called dynamic top talkers allows real-time sorting and aggregation of NetFlow data. Also shown is a show MLS command to view the hardware cache on the Cisco Catalyst 6500 Series Switch.
The following is the original NetFlow show command used for many years in Cisco IOS Software. Information provided includes packet size distribution; basic statistics about number of flows and export timer setting, a view of the protocol distribution statistics and the NetFlow cache.
The “show ip cache flow” command displays a summary of the NetFlow accounting statistics.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/prod_white_paper0900aecd80406232.html