200-125 Exam
Actual 200-125 faq Reviews & Tips
There are a variety associated with positive aspects after getting purchased your Cisco 200-125 documentation. A 200-125 documentation is often a form of assurance that youve the very best amount of understanding in connection with The item section so you are able to eliminate most of issues that the place from it suffers from. On top of that, this 200-125 documentation as well as improving your price in the sight of this businesses. If you are searching for a job, this 200-125 documentation will help you to have the most effective job. If you are searching regarding promo, this 200-125 documentation could make this easy for people. In addition, this 200-125 documentation build up your valuation within your provider likewise.
2021 Sep 200-125 free practice test
Q151. - (Topic 2)
A switch is configured with all ports assigned to VLAN 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?
A. More collision domains will be created.
B. IP address utilization will be more efficient.
C. More bandwidth will be required than was needed previously.
D. An additional broadcast domain will be created.
Answer: D
Q152. - (Topic 7)
Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
Which path does traffic take from R1 to R5?
A. The traffic goes through R2.
B. The traffic goes through R3.
C. The traffic is equally load-balanced over R2 and R3.
D. The traffic is unequally load-balanced over R2 and R3.
Answer: A
Q153. - (Topic 9)
What is the purpose of the POST operation on a router?
A. determine whether additional hardware has been added
B. locate an IOS image for booting
C. enable a TFTP server
D. set the configuration register
Answer: A
Q154. - (Topic 8)
RouterA is unable to reach RouterB. Both routers are running IOS version 12.0.
After reviewing the command output and graphic, what is the most likely cause of the problem?
A. incorrect bandwidth configuration
B. incorrect LMI configuration
C. incorrect map statement
D. incorrect IP address
Answer: C
Q155. - (Topic 9)
Which step in the router boot process searches for an IOS image to load into the router?
A. bootstrap
B. POST
C. mini-IOS
D. ROMMON mode
Answer: A
Renovate 200-125 latest exam:
Q156. - (Topic 4)
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth
B. Bandwidth and Delay
C. Bandwidth, Delay, and MTU
D. Bandwidth, MTU, Reliability, Delay, and Load
Answer: A
Q157. - (Topic 9)
Which two features can dynamically assign IPv6 addresses? (Choose two.)
A. IPv6 stateless autoconfiguration
B. DHCP
C. NHRP
D. IPv6 stateful autoconfiguration
E. ISATAP tunneling
Answer: A,B
Q158. - (Topic 7)
Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
Why are the pings failing?
A. The network statement is missing on R5.
B. The loopback interface is shut down on R5.
C. The network statement is missing on R1.
D. The IP address that is configured on the Lo1 interface on R5 is incorrect.
Answer: C
Q159. - (Topic 5)
Syslog was configured with a level 3 trap. Which 3 types of logs would be generated (choose four)
A. Emergencies
B. Alerts
C. Critical
D. Errors
E. Warnings
Answer: A,B,C,D
Q160. - (Topic 4)
Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D