200-125 Exam
Top 10 questions 200-125 for IT candidates (111 to 120)
Proper study guides for Refresh Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certified begins with Cisco 200-125 preparation products which designed to deliver the Exact 200-125 questions by making you pass the 200-125 test at your first time. Try the free 200-125 demo right now.
2021 Sep 200-125 question
Q111. - (Topic 8)
What command is used to verify the DLCI destination address in a Frame Relay static configuration?
A. show frame-relay pvc
B. show frame-relay lmi
C. show frame-relay map
D. show frame relay end-to-end
Answer: C
Q112. - (Topic 9)
Which command can you enter to route all traffic that is destined for 192.168.0.0/20 to a specific interface?
A. router(config)#ip route 192.168.0.0 255.255.240.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.0 GigabitEthernet0/1
C. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
D. router(config)#ip route 192.168.0.0 255.255.255.0 GigabitEthernet0/1
Answer: A
Q113. - (Topic 6)
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security mac-address 1
Answer: C
Q114. - (Topic 4)
What OSPF command, when configured, will include all interfaces into area 0?
A. network 0.0.0.0 255.255.255.255 area 0
B. network 0.0.0.0 0.0.0.0 area 0
C. network 255.255.255.255 0.0.0.0 area 0
D. network all-interfaces area 0
Answer: A
Q115. - (Topic 2)
Refer to the exhibit.
How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?
A. The ports only need to be connected by a crossover cable.
B. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
C. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode access
SwitchX(config-if)# switchport access vlan 1
D. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
SwitchX(config-if)# switchport trunk vlan 1
SwitchX(config-if)# switchport trunk vlan 10
SwitchX(config-if)# switchport trunk vlan 20
Answer: B
Most recent 200-125 exams:
Q116. - (Topic 5)
Which two statements about static NAT translations are true? (Choose two.)
A. They allow connections to be initiated from the outside.
B. They require no inside or outside interface markings because addresses are statically defined.
C. They are always present in the NAT table.
D. They can be configured with access lists, to allow two or more connections to be initiated from the outside.
Answer: A,C
Q117. - (Topic 1)
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?
A. Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B. Add a second router to handle the VLAN traffic.
C. Add two more Fast Ethernet interfaces.
D. Implement a router-on-a-stick configuration.
Answer: D
Q118. DRAG DROP - (Topic 7)
Answer:
Q119. - (Topic 4)
Refer to the exhibit.
The network administrator requires easy configuration options and minimal routing protocol traffic. What two options provide adequate routing table information for traffic that passes between the two routers and satisfy the requests of the network administrator? (Choose two.)
A. a dynamic routing protocol on InternetRouter to advertise all routes to CentralRouter.
B. a dynamic routing protocol on InternetRouter to advertise summarized routes to CentralRouter.
C. a static route on InternetRouter to direct traffic that is destined for 172.16.0.0/16 to CentralRouter.
D. a dynamic routing protocol on CentralRouter to advertise all routes to InternetRouter.
E. a dynamic routing protocol on CentralRouter to advertise summarized routes to InternetRouter.
F. a static, default route on CentralRouter that directs traffic to InternetRouter.
Answer: C,F
Q120. - (Topic 4)
Refer to the exhibit.
Which of these statements correctly describes the state of the switch once the boot process has been completed?
A. As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B. Remote access management of this switch will not be possible without configuration change.
C. More VLANs will need to be created for this switch.
D. The switch will need a different IOS code in order to support VLANs and STP.
Answer: B