300-115 Exam
10 tips on 9tut ccnp switch 300 115
Master the ccnp switch 300 115 dumps pdf Implementing Cisco IP Switched Networks content and be ready for exam day success quickly with this Pass4sure ccnp 300 115 dumps practice test. We guarantee it!We make it a reality and give you real ccnp switch 300 115 dumps questions in our Cisco cisco 300 115 braindumps.Latest 100% VALID Cisco 300 115 dumps Exam Questions Dumps at below page. You can use our Cisco 300 115 dumps braindumps and pass your exam.
Q11. after configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer notices that none of the VTP clients are receiving the updates. What is the problem?
A. The VTP server must be reloaded.
B. The VTP version number must be set to version 3.
C. After each update to the VTP server, it takes up to 4 hours propagate.
D. VTP must be stopped and restarted on the server.
E. Another switch in the domain has a higher revision number than the server.
Answer: B
Q12. Refer to the exhibit.
What is the result of the configuration?
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.
Answer: B
Q13. When you configure a private VLAN, which type of port must you configure the gateway router port as?
A. promiscuous port
B. isolated port
C. community port
D. access port
Answer: A
Q14. Which SDM template disables routing and supports the maximum number of unicast MAC addresses?
A. VLAN
B. access
C. default
D. routing
Answer: A
Q15. Which statement about the use of SDM templates in a Cisco switch is true?
A. SDM templates are used to configure system resources in the switch to optimize support for specific features, depending on how the switch is used in the network.
B. SDM templates are used to create Layer 3 interfaces (switch virtual interfaces) to permit hosts in one VLAN to communicate with hosts in another VLAN.
C. SDM templates are used to configure ACLs that protect networks and specific hosts from unnecessary or unwanted traffic.
D. SDM templates are used to configure a set of ACLs that allows the users to manage the flow of traffic handled by the route processor.
E. SDM templates are configured by accessing the switch using the web interface.
Answer: A
Q16. Refer to the exhibit.
The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing from the database. Which action resolves this problem?
A. Disable VTP pruning and disable 802.1q.
B. Update the VTP revision number.
C. Change VTP mode to server and enable 802.1q.
D. Enable VTP pruning and disable 802.1q.
Answer: C
Q17. The command storm-control broadcast level 75 65 is configured under the switch port connected to the corporate mail server. In which three ways does this command impact the traffic? (Choose three.)
A. SNMP traps are sent by default when broadcast traffic reaches 65% of the lower-level threshold.
B. The switchport is disabled when unicast traffic reaches 75% of the total interface bandwidth.
C. The switch resumes forwarding broadcasts when they are below 65% of bandwidth.
D. Only broadcast traffic is limited by this particular storm control configuration.
E. Multicast traffic is dropped at 65% and broadcast traffic is dropped at 75% of the total interface bandwidth.
F. The switch drops broadcasts when they reach 75% of bandwidth.
Answer: CDF
Q18. Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Answer: C
Q19. A network engineer configured a fault-tolerance link on Gigabit Ethernet links G0/1, G0/2, G0/3, and G0/4 between two switches using Ethernet port-channel. Which action allows interface G0/1 to always actively forward traffic in the port-channel?
A. Configure G0/1 as half duplex and G0/2 as full duplex.
B. Configure LACP port-priority on G0/1 to 1.
C. Configure LACP port-priority on G0/1 to 65535.
D. LACP traffic goes through G0/4 because it is the highest interface ID.
Answer: B
Q20. Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?
A. promiscuous port
B. isolated port
C. community port
D. trunk port
Answer: A