300-115 Exam
Amazing certprepare 300 115 secrets
Act now and download your Cisco ccnp 300 115 pdf test today! Do not waste time for the worthless Cisco ccnp switch 300 115 pdf tutorials. Download Abreast of the times Cisco Implementing Cisco IP Switched Networks exam with real questions and answers and begin to learn Cisco 300 115 vce with a classic professional.
Q61. Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?
A. ip dhcp snooping trust
B. ip dhcp snooping
C. ip dhcp trust
D. ip dhcp snooping information
Answer: A
Q62. Refer to the exhibit.
What is the result of the SPAN configuration on a Cisco switch?
A. Configure a SPAN session to monitor the received traffic on interface g0/4 only for VLAN 3.
B. Configure a SPAN session to monitor the received traffic on interface g0/4 for all VLANs except VLAN 3.
C. Configure a SPAN session to monitor the received traffic on interface g0/5 only for VLAN 3.
D. Configure a SPAN session to monitor the received traffic on interface g0/5 for all VLANs except VLAN 3.
Answer: A
Q63. Which statement about the UDLD protocol is true?
A. UDLD is a Cisco-proprietary Layer 2 protocol that enables devices to monitor the physical status of links and detect unidirectional failures.
B. UDLD is a Cisco-proprietary Layer 2 protocol that enables devices to advertise their identity, capabilities, and neighbors on a local area network.
C. UDLD is a standardized Layer 2 protocol that enables devices to monitor the physical status of links and detect unidirectional failures.
D. UDLD is a standardized Layer 2 protocol that enables devices to advertise their identity, capabilities, and neighbors on a local area network.
Answer: A
Q64. Refer to the exhibit.
A multilayer switch has been configured to send and receive encapsulated and tagged frames. VLAN 2013 on the multilayer switch is configured as the native VLAN. Which option is the cause of the spanning-tree error?
A. VLAN spanning-tree in SW-2 is configured.
B. spanning-tree bpdu-filter is enabled.
C. 802.1q trunks are on both sides, both with native VLAN mismatch.
D. VLAN ID 1 should not be used for management traffic because its unsafe.
Answer: C
Q65. A network engineer is installing a switch for temporary workers to connect to. The engineer does not want this switch participating in Spanning Tree with the rest of the network; however, end user connectivity is still required. Which spanning-tree feature accomplishes this?
A. BPDUblock
B. BPDUfilter
C. BPDUignore
D. BPDUguard
E. BPDUdisable
Answer: B
Q66. Which option lists the modes that are available for configuring UDLD on a Cisco switch?
A. normal and aggressive
B. active and aggressive
C. normal and active
D. normal and passive
E. normal and standby
Answer: A
Q67. Refer to the exhibit.
When troubleshooting a network problem, a network analyzer is connected to Port f0/1 of a LAN switch. Which command can prevent BPDU transmission on this port?
A. spanning-tree portfast bpduguard enable
B. spanning-tree bpduguard default
C. spanning-tree portfast bpdufilter default
D. no spanning-tree link-type shared
Answer: C
Q68. What is the maximum number of virtual MAC addresses that GLBP allows per group?
A. 2
B. 4
C. 6
D. 8
Answer: B
Q69. Which authentication service is needed to configure 802.1x?
A. RADIUS with EAP Extension
B. TACACS+
C. RADIUS with CoA
D. RADIUS using VSA
Answer: A
Q70. Which command correctly configures standby tracking for group 1 using the default decrement priority value?
A. standby 1 track 100
B. standby 1 track 100 decrement 1
C. standby 1 track 100 decrement 5
D. standby 1 track 100 decrement 20
Answer: A