300-135 Exam
Ultimate Guide: ccnp tshoot 300 135 pdf
It is more faster and easier to pass the Cisco ccnp tshoot 300 135 pdf exam by using Virtual Cisco TSHOOT Troubleshooting and Maintaining Cisco IP Networks questuins and answers. Immediate access to the Renovate tshoot 300 135 pdf Exam and find the same core area ccnp tshoot 300 135 dumps questions with professionally verified answers, then PASS your exam with a high score now.
P.S. Virtual 300-135 software are available on Google Drive, GET MORE: https://drive.google.com/open?id=1A41WbBid6qAvgj4lSRDdo8qGNitx8ULz
New Cisco 300-135 Exam Dumps Collection (Question 7 - Question 16)
Q7. Which of the following statements regarding documentation would not be considered a helpful step in the troubleshooting process?
A. Use the Cisco Auto Configuration tool.
B. Use the Cisco Rollback feature.
C. Automate documentation.
D. Schedule documentation checks.
E. Use the Cisco Configuration Archive tool.
F. Require documentation prior to a ticket being closed out.
Answer: A
Q8. Which of the following pieces of information will the command show interface provide? (Choose all that apply.)
A. Layer 1 status
B. Output queue drops
C. Interface CPU utilization
D. Cable type connected to interface
E. Layer 2 status
F. Input queue drops
Answer: A,B,E,F
Q9. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241
address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. BGP
B. NTP
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: D
Explanation:
On R1, for IPV4 authentication of OSPF the command is missing and required to configure-
----- ip ospf authentication message-digest
Q10. Scenario:
You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn't appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems.
Examine the configuration on R5. Router R5 do not see any route entries learned from R4; what could be the issue?
A. HSRP issue between R5 and R4
B. There is an OSPF issue between R5and R4
C. There is a DHCP issue between R5 and R4
D. The distribute-list configured on R5 is blocking route entries
E. The ACL configured on R5 is blocking traffic for the subnets advertised from R4.
Answer: B
Explanation:
If we issue the u201cshow ip routeu201d and u201cshow ip ospf neighboru201d commands on R5, we see that there are no learned OSPF routes and he has no OSPF neighbors.
Q11. The implementation group has been using the test bed to do an IPv6 'proof-of- concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
Use the supported commands to isolate the cause of this fault and answer the following question.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: C
Explanation:
Start to troubleshoot this by pinging the loopback IPv6 address of DSW2 (2026::102:1). This can be pinged from DSW1, and R4, but not R3 or any other devices past that point. If we look at the routing table of R3, we see that there is no OSPF neighbor to R4:
Screen Shot 2015-03-11 at 4
This is due to mismatched tunnel modes between R3 and R4:
Screen Shot 2015-03-11 at 4
Problem is with R3, and to resolve the issue we should delete the u201ctunnel mode ipv6u201d under interface Tunnel 34.
Q12. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
Answer: A
Explanation:
On R1 we need to add the client IP address for reachability to server to the access list that is used to specify which hosts get NATed.
Q13. A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems.
Refer to the topology.
SW1 Switch Management IP address is not pingable from SW4. What could be the issue?
A. Management VLAN not allowed in the trunk links between SW1 and SW4
B. Management VLAN not allowed in the trunk links between SW1 and SW2
C. Management VLAN not allowed in the trunk link between SW2 and SW4
D. Management VLAN ip address on SW4 is configured in wrong subnet
E. Management VLAN interface is shutdown on SW4
Answer: D
Explanation:
In the network, VLAN 300 is called the Management VLAN. Based on the configurations shown below, SW1 has VLAN 300 configured with the IP address of 192.168.10.1/24, while on SW4 VLAN 300 has an IP address of 192.168.100.4/24, which is not in the same subnet.
Q14. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
What is the solution to the fault condition?
A. Under the global configuration, delete the no ip dhcp use vrf connected command.
B. Under the IP DHCP pool configuration, delete the default -router 10.2.1.254 command
and enter the default-router 10.1.4.5 command.
C. Under the IP DHCP pool configuration, delete the network 10.2.1.0 255.255.255.0 command and enter the network 10.1.4.0 255.255.255.0 command.
D. Under the IP DHCP pool configuration, issue the no ip dhcp excluded-address 10.2.1.1 10.2.1.253 command and enter the ip dhcp excluded-address 10.2.1.1 10.2.1.2 command.
Answer: D
Explanation:
On R4 the DHCP IP address is not allowed for network 10.2.1.0/24 which clearly shows the problem lies on R4 & the problem is with DHCP
Q15. The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble
ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. BGP
B. NTP
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: C
Explanation:
On R1 we need to add the client IP address for reachability to server to the access list that is used to specify which hosts get NATed.
Q16. Which of the following commands can be used to gather information about the AS- PATH of a BGP route? (Choose all that apply.)
A. show ip bgp neighbors
B. debug ip bgp updates
C. show ip route bgp
D. show ip bgp
E. show ip bgp summary
F. sh ip bgp database
Answer: B,D
Explanation: Incorrect:
show ip bgp summary: The command show ip bgp summary does not presents informations about routes.
P.S. Easily pass 300-135 Exam with Allfreedumps Virtual Dumps & pdf vce, Try Free: https://www.allfreedumps.com/300-135-dumps.html (129 New Questions)