Exambible offers free demo for 400 101 vce exam. "CCIE Routing and Switching (v5.0)", also known as ccie 400 101 dumps exam, is a Cisco Certification. This set of posts, Passing the Cisco 400 101 dumps exam, will help you answer those questions. The 400 101 pdf Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco 400 101 dumps exams and revised by experts!
P.S. Validated 400-101 braindumps are available on Google Drive, GET MORE: https://drive.google.com/open?id=1cF02oX7GSasuEXS-dBzgjdZ6VV4eo-Md
Q14. Which feature can mitigate hung management sessions?
A. Contru00f6l Plane Policing
B. the service tcp-keepalives-in and service tcp-keepalives-out commands
C. the servicu00ea tcp-small servers command
D. vty line ACLs
Answer: B
Q15. Which two statements about IGMP are true?(Choose two.)
A. IGMPv2 supports explicit source signaling.
B. IGMPv3 is the first version of IGMP to support a basic query-response mechanism.
C. IGMPv2 supports IGMP querier election.
D. IGMPvl supports group-specific queries.
E. IGMPv3 uses 224.0.0.22 as destination address for reports.
Answer: C,E
Q16. Which two events occur when a packets is decapsulated in a GRE tunnel? (Choose two.)
A. The source IPv4 address in the IPv4 payload is used to forward the packet.
B. The destination IPv4 address in the IPv4 payload is used to forward of the packets.
C. The version field of the GRE header is incremented.
D. The GRE keepalive mechanism is reset.
E. The TTL of the payload packet is incremented.
F. The TTL of the payload is discremented.
Answer: B,E
Q17. Which extended ping IP header option allows you to specify one or more hops over which the packets will travel without specifying the full path?
A. verbose
B. loose
C. strict
D. record
Answer: B
Q18. Which three actions are required when configuration NAT-PT? (choose three.
A. Specify a ::/48 prefix that will map to a MAC address.
B. Specify a::/32 prefix that will map to an IPV6 address.
C. Specify an IPv6-to-IPv4 translation.
D. Enable NAT-PT Globally.
E. Specify a ::/96 prefix that will map to an IPv4 address.
F. Specify an IPv4-to-IPv6 translation.
Answer: C,E,F
Q19. Which value does EIGRP use to determine the metric for a summary address?
A. The average of the component metrics
B. A default fixed value
C. The lowest metric among the component routes
D. The highest metric among the component routes
Answer: C
Q20. Which two statements about NBAR classification are true?(choose two)
A. It requires CEF to be enable on the router
B. It is recommended for capacity planning
C. It can classify IP packets
D. It cannot distinguish UDP flows
E. It can classify MPLS packets
Answer: A,D
Q21. Which two statements about Cisco Express Forwarding load balancing are true?(choose two)
A. Each hash maps directly to a single entry in the RIB
B. Cisco Express Forwarding can load-balance over o maximum of two destinations
C. It combines the source and destination IP address to create a hash for each destination
D. It combines the source IP address subnet mask to create a hash for each destination
E. Each hash maps directly to a single entry in the adjacency table
Answer: C,E
Q22. Which two statements about Embedded Packet Capture are true? (Choose two)
A. Multicast packets are captured only on ingress
B. It can capture Ipv4 packets only
C. Cisco Express Forwarding must be enabled
D. Captures must be decoded offline
E. Only a single capture point can be activated per interface
Answer: A,C
Q23. R2#router ospf 1
router-id 10.2.2.2
log-adjacency changes
network 192.168.19.0 0.0.0.255 area 0
R2#show ip ospf
Routing Process "ospf 1" with ID 10.1.1.1
Start time: 00:00:32.552, Time elapsed: 00:03:00.996 Supports only single TOS(TOS0) routes
Supports opaque LSA
Supports Link-local Signaling (LLS) Supports area transit capability
Router is not originating router-LSAs with maximum metric Initial SPF schedule delay 5000 msecs
Refer to the exhibit. After you applied a new configuration to router R2, you executed the show ip ospf
command and noticed that the new router ID was missing. Which two actions can you take to resolve the problem?
A. Reload the router
B. Wait for the hello-interval to elapse
C. Issue the clear ip route command
D. Issue the clear ip ospf command
E. Execute a shutdown followed by a no shutdown on the OSRF interfaces
F. Wait for the dead-interval to elapse
Answer: A,D
Recommend!! Get the Validated 400-101 dumps in VCE and PDF From Thedumpscentre, Welcome to download: http://www.thedumpscentre.com/400-101-dumps/ (New 911 Q&As Version)