NSE5 Exam
Updated Fortinet NSE5 - An Overview 81 to 90
It is impossible to pass Fortinet NSE5 exam without any help in the short term. Come to Actualtests soon and find the most advanced, correct and guaranteed Fortinet NSE5 practice questions. You will get a surprising result by our Up to the minute Fortinet Network Security Expert 5 Written Exam (500) practice guides.
Q81. - (Topic 2)
Examine the Exhibit shown below; then answer the question following it.
The Vancouver FortiGate unit initially had the following information in its routing table:
S 172.20.0.0/16 [10/0] via 172.21.1.2, port2
C 172.21.0.0/16 is directly connected, port2
C 172.11.11.0/24 is directly connected, port1
Afterwards, the following static route was added:
config router static
edit 6
set dst 172.20.1.0 255.255.255.0
set pririoty 0
set device port1
set gateway 172.11.12.1
next
end
Since this change, the new static route is NOT showing up in the routing table. Given the information provided, which of the following describes the cause of this problem?
A. The subnet 172.20.1.0/24 is overlapped with the subnet of one static route that is already in the routing table (172.20.0.0/16), so, we need to enable allow-subnet-overlap first.
B. The 'gateway' IP address is NOT in the same subnet as the IP address of port1.
C. The priority is 0, which means that the route will remain inactive.
D. The static route configuration is missing the distance setting.
Answer: B
Q82. - (Topic 1)
A FortiGate unit can provide which of the following capabilities? (Select all that apply.)
A. Email filtering
B. Firewall
C. VPN gateway
D. Mail relay
E. Mail server
Answer: A,B,C
Q83. - (Topic 2)
Review the output of the command config router ospf shown in the Exhibit below; then answer the question following it.
Which one of the following statements is correct regarding this output?
A. OSPF Hello packets will only be sent on interfaces configured with the IP addresses
172.16.1.1 and 172.16.1.2.
B. OSPF Hello packets will be sent on all interfaces of the FortiGate device.
C. OSPF Hello packets will be sent on all interfaces configured with an address matching the 10.0.1.0/24 and 172.16.0.0/12 networks.
D. OSPF Hello packets are not sent on point-to-point networks.
Answer: C
Q84. - (Topic 1)
A client can establish a secure connection to a corporate network using SSL VPN in tunnel mode.
Which of the following statements are correct regarding the use of tunnel mode SSL VPN? (Select all that apply.)
A. Split tunneling can be enabled when using tunnel mode SSL VPN.
B. Client software is required to be able to use a tunnel mode SSL VPN.
C. Users attempting to create a tunnel mode SSL VPN connection must be authenticated by at least one SSL VPN policy.
D. The source IP address used by the client for the tunnel mode SSL VPN is assigned by the FortiGate unit.
Answer: A,B,C,D
Q85. - (Topic 3)
Based on the web filtering configuration illustrated in the exhibit,
which one of the following statements is not a reasonable conclusion?
A. Users can access both the www.google.com site and the www.fortinet.com site.
B. When a user attempts to access the www.google.com site, the FortiGate unit will not perform web filtering on the content of that site.
C. When a user attempts to access the www.fortinet.com site, any remaining web filtering will be bypassed.
D. Downloaded content from www.google.com will be scanned for viruses if antivirus is enabled.
Answer: B
Q86. - (Topic 3)
A FortiGate unit is operating in NAT/Route mode and is configured with two Virtual LAN (VLAN) sub-interfaces added to the same physical interface.
Which of the following statements is correct regarding the VLAN IDs in this scenario?
A. The two VLAN sub-interfaces can have the same VLAN ID only if they have IP addresses in different subnets.
B. The two VLAN sub-interfaces must have different VLAN IDs.
C. The two VLAN sub-interfaces can have the same VLAN ID only if they belong to different VDOMs.
D. The two VLAN sub-interfaces can have the same VLAN ID if they are connected to different L2 IEEE 802.1Q compliant switches.
Answer: B
Q87. - (Topic 3)
Both the FortiGate and FortiAnalyzer units can notify administrators when certain alert conditions are met.
Considering this, which of the following statements is NOT correct?
A. On a FortiGate device, the alert condition is based either on the severity level or on the log type, but not on a combination of the two.
B. On a FortiAnalyzer device, the alert condition is based either on the severity level or on the log type, but not on a combination of the two.
C. Only a FortiAnalyzer device can send the alert notification in the form of a syslog message.
D. Both the FortiGate and FortiAnalyzer devices can send alert notifications in the form of an email alert.
Answer: B
Q88. - (Topic 1)
The command structure of the CLI on a FortiGate unit consists of commands, objects, branches, tables and parameters. Which of the following items describes port1?
A. A command.
B. An object.
C. A table.
D. A parameter.
Answer: C
Q89. - (Topic 3)
An administrator wishes to generate a report showing Top Traffic by service type. They notice that web traffic overwhelms the pie chart and want to exclude the web traffic from the report.
Which of the following statements best describes how to do this?
A. In the Service field of the Data Filter, type 80/tcp and select the NOT checkbox.
B. Add the following entry to the Generic Field section of the Data Filter: service="!web".
C. When editing the chart, uncheck wlog to indicate that Web Filtering data is being excluded when generating the chart.
D. When editing the chart, enter 'http' in the Exclude Service field.
Answer: A
Q90. - (Topic 1)
An end user logs into the full-access SSL VPN portal and selects the Tunnel Mode option by clicking on the “Connect” button. The administrator has enabled split tunneling.
Given that the user authenticates against the SSL VPN policy shown in the image below, which statement below identifies the route that is added to the client’s routing table.
A. A route to destination matching the ‘WIN2K3’ address object.
B. A route to the destination matching the ‘all’ address object.
C. A default route.
D. No route is added.
Answer: A