156-915.80 Exam
Top Precise 156-915.80 practice exam Tips!
Cause all that matters here is passing the Check Point 156-915.80 exam. Cause all that you need is a high score of 156-915.80 Check Point Certified Security Expert Update - R80 exam. The only one thing you need to do is downloading Pass4sure 156-915.80 exam study guides now. We will not let you down with our money-back guarantee.
P.S. Simulation 156-915.80 faq are available on Google Drive, GET MORE: https://drive.google.com/open?id=10nZGq46vgX7-YMephRQOtbIjmfJ8w6LL
New Check Point 156-915.80 Exam Dumps Collection (Question 6 - Question 15)
Question No: 6
Which of these options is an implicit MEP option?
A. Primary-backup
B. Source address based
C. Round robin
D. Load Sharing
Answer: A
Explanation:
There are three methods to implement implicit MEP:
First to Respond, in which the first Security Gateway to reply to the peer Security Gateway is chosen. An organization would choose this option if, for example, the organization has two Security Gateways in a MEP
configuration - one in London, the other in New York. It makes sense for VPN-1 peers located in England to try the London Security Gateway first and the NY Security Gateway second. Being geographically closer to VPN peers in England, the London Security Gateway is the first to respond, and becomes the entry point to the internal network. See: First to Respond.
Primary-Backup, in which one or multiple backup Security Gateways provide "high availability" for a primary Security Gateway. The remote peer is configured to work with the primary Security Gateway, but switches to the backup Security Gateway if the primary goes down. An organization might decide to use this configuration if it has two machines in a MEP environment, one of which is stronger than the other. It makes sense to configure the stronger machine as the primary. Or perhaps both machines are the same in terms of strength of performance, but one has a cheaper or faster connection to the Internet. In this case, the machine with the better Internet connection should be configured as the primary. See: Primary-Backup Security Gateways.
Load Distribution, in which the remote VPN peer randomly selects a Security Gateway with which to open a connection. For each IP source/destination address pair, a new Security Gateway is randomly selected. An organization might have a number of machines with equal performance abilities. In this case, it makes
sense to enable load distribution. The machines are used in a random and equal way. See: Random Selection.
Question No: 7
Where is it necessary to configure historical records in SmartView Monitor to generate Express reports in SmartReporter?
A. In SmartDashboard, the SmartView Monitor page in the R80 Security Gateway object
B. In SmartReporter, under Express > Network Activity
C. In SmartReporter, under Standard > Custom
D. In SmartView Monitor, under Global Properties > Log and Masters
Answer: A
Question No: 8
Your expanding network currently includes ClusterXL running Multicast mode on two members, as shown in this topology:
Exhibit:
You need to add interfaces: 10.10.10.1/24 on Member A, and 10.10.10.2/24 on Member B. The virtual IP address for these interfaces is 10.10.10.3/24. Both cluster gateways have a Quad card with an available eth3 interface. What is the correct procedure to add these interfaces?
A. 1. Disable "Cluster membership" from one Gateway via cpconfig.2. Configure the new interface via sysconfig from the "non-member" Gateway.3. Re-enable "Cluster membership" on the Gateway.4. Perform the same steps on the other Gateway.5. Update the topology in the cluster object.6. Install the Security Policy.
B. 1. Configure the new interface on both members using WebUI.2. Update the new topology in the cluster
object from SmartDashboard.3. Define virtual IP in the Dashboard4. Install the Security Policy.
C. 1. Use WebUI to configure the new interfaces on both member.2. Update the topology in the cluster object.3. Reboot both gateways.4. Install the Security Policy.
D. 1. Use the command ifconfig to configure and enable the new interface on both members.2. Update the topology in the cluster object for the cluster and both members.3. Install the Security Policy.4. Reboot the gateway.
Answer: B
Question No: 9
When using GAiA, it might be necessary to temporarily change the MAC address of the interface eth 0 to 00:0C:29:12:34:56. After restarting the network the old MAC address should be active. How do you configure this change?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: A
Question No: 10
Which packet info is ignored with Session Rate Acceleration?
A. source port ranges
B. source ip
C. source port
D. same info from Packet Acceleration is used
Answer: C
Question No: 11
MultiCorp is located in Atlanta. It has a branch office in Europe, Asia, and Africa. Each location has its own AD controller for local user login. How many ADqueries have to be configured?
Answer:
4
Question No: 12
Using mgmt_cli, what is the correct syntax to import a host object called Server_1 from the CLI?
A. mgmt_cli add-host u201cServer_1u201d ip_ address u201c10.15.123.10u201d u2013 format txt
B. mgmt_ cli add host name u201cServer_ 1u201d ip-address u201c10.15.123.10u201d u2013 format json
C. mgmt_ cli add object-host u201cServer_ 1u201d ip-address u201c10.15.123.10u201d u2013 format json
D. mgmt_cli add object u201cServer_ 1u201d ip-address u201c10.15.123.10u201d u2013 format json
Answer: B
Explanation: Example:
mgmt_cli add host name "New Host 1" ip-address "192.0.2.1" --format json
u2022 "--format json" is optional. By default the output is presented in plain text.
Question No: 13
How could you compare the Fingerprint shown to the Fingerprint on the server? Exhibit:
A. Run cpconfig, select the Certificate's Fingerprint option and view the fingerprint
B. Run cpconfig, select the GUI Clients option and view the fingerprint
C. Run cpconfig, select the Certificate Authority option and view the fingerprint
D. Run sysconfig, select the Server Fingerprint option and view the fingerprint
Answer: A
Question No: 14
How do you recover communications between your Security Management Server and Security Gateway if you lock yourself out through a rule or policy mis-configuration?
A. fw unload policy
B. fw unloadlocal
C. fw delete all.all@localhost
D. fwm unloadlocal
Answer: B
Question No: 15
You are the Security Administrator for MegaCorp. A Check Point firewall is installed and in use on a platform using GAiA. You have trouble configuring the speed and duplex settings of your Ethernet interfaces. Which of the following commands can be used in CLISH to configure the speed and duplex settings of an Ethernet interface and will survive a reboot? Give the BEST answer.
A. ethtool
B. set interface <options>
C. mii_tool
D. ifconfig -a
Answer: B
Recommend!! Get the Simulation 156-915.80 dumps in VCE and PDF From Certleader, Welcome to download: https://www.certleader.com/156-915.80-dumps.html (New Q&As Version)