NEW QUESTION 1
When defining an explicit MPLS TE tunnel path, which two command options are available under the explicit-path configuration mode? (Choose two.)

• A. exclude-address
• B. include-address
• C. next-address
• D. dynamic-address

Answer: AC

NEW QUESTION 2
Given this configuration of an interface for MPLS traffic engineering on a Cisco IOS XE router:
interface POS1/1/0 mpls traffic-eng tunnels ip rsvp bandwidth 5000
Which option lists the equivalent configurations required on a Cisco IOS XR router?

• A. interface POS1/1/0 mpls traffic-eng tunnels ip rsvp bandwidth 5000
• B. mpls traffic-eng interface POS1/1/0
• C. mpls traffic-eng interface POS1/1/1 bandwidth 5mb
• D. mpls traffic-eng interface POS1/1/0 rsvpinterface POS1/1/0
• E. mpls traffic-eng interface POS1/1/0 rsvpinterface POS1/1/0 bandwidth 5000

Answer: E

NEW QUESTION 3
Cisco MPLS TE path setup can be affected by which three tunnel attributes? (Choose three.)

• A. bandwidth
• B. delay
• C. MTU
• D. priority
• E. affinity

Answer: ADE

NEW QUESTION 4
Which QoS technique can be used to protect customer traffic from being dropped by traffic rate limiting performed by the service provider?

• A. LLQ
• B. policing
• C. fair-queue
• D. shaping

Answer: D

NEW QUESTION 5
When a link flaps, an mpls ldp session will also flap. Which feature minimizes traffic loss and provides faster convergence after the link is re-established?

• A. BFD
• B. MPLS LDP IGP SYNC
• C. graceful restart
• D. LDP session protection
• E. LDP nonstop routing

Answer: D

NEW QUESTION 6
DRAG DROP

Answer:

Explanation: Place the options in the following order: Uniform Mode
Short-Pipe Mode Pipe Mode

NEW QUESTION 7
Which four options are methods by which labels can be assigned in the label stack to an IP prefix? (Choose four.)

• A. LDP
• B. CEF
• C. BGP
• D. RSVP
• E. static
• F. IGP
• G. route recursion
• H. manual tagging

Answer: ACDG

NEW QUESTION 8
A network engineer must analyze RSVP-TE signaling on a syslog server. Which three RSVP messages are valid? (Choose three.)

• A. RSVP PATH
• B. RSVP RESERVATION
• C. RSVP ESTABLISHED
• D. RSVP PATH TEAR
• E. RSVP KILL
• F. RSVP INIT

Answer: ABD

NEW QUESTION 9
A network operations center analyzes a Wireshark capture and tries to verify which QoS policy is effective over a customer router. How many bits define the DSCP values?

• A. 3
• B. 6
• C. 8
• D. 16

Answer: B

NEW QUESTION 10
Which are typical class-based marking policies that are implemented on service provider IP NGN PE routers?

• A. On the PE ingress, classify the customer traffic and then mark with qos-grou
• B. On the PE egress, classify based on the qos-group and then mark with mpls exp.
• C. On the PE ingress, classify the customer traffic and then mark with mpls ex
• D. On the PE egress, classify based on the mpls exp and then mark with qos-group.
• E. On the PE ingress, trust the customer QoS marking
• F. On the PE egress, classify based on the customer QoS markings and then mark with qos-group.
• G. On the PE ingress, trust the customer QoS marking
• H. On the PE egress, classify based on the customer QoS markings and then mark with mpls exp.

Answer: A

NEW QUESTION 11
How many labels does an MPLS packet have, with a bottom-of-stack label set to zero?

• A. The packet has no label.
• B. The packet has one label.
• C. The packet may have one or more labels.
• D. The packet has at least two labels.

Answer: D

NEW QUESTION 12
Scenario:




On CE7 which statement is correct regarding Traffic the QoS policy applied to the gi0/0 interface in the input direction?

• A. Traffic matching the "MARKING2" class-map will be marked with qos-group 5
• B. Traffic matching the "MARKING1" class-map will be marked with MPLS EXP 5
• C. All incoming packets not matched bythe"MARKING1" class-map will be dropped
• D. All incoming packets with the DSCP EF marking with be marked with MPLS EXP 0

Answer: B

Explanation: Issue: show policy-map interface gi0/0
First find out which policy-map is applied (it called something like QOSPOLICY1)
A is wrong. Class MARKING2 is indeed defined but not applied to that policy-map. There are two class-maps applied MARKING1 and class-default. Both will mark the traffic with MPLS EXP values.
default:
set mpls experimental imposition 0 MARKING1
set mpls experimental imposition 5

NEW QUESTION 13
Which three fields must be the same in an IPv6 header to consider different packets on the same flow? (Choose three.)

• A. source port
• B. destination address
• C. destination port
• D. source address
• E. flow label
• F. transport protocol type

Answer: BDE

NEW QUESTION 14
Which three commands are used to troubleshoot why IP packets are not forwarded on the LSP? (Choose three.)

• A. show cef prefix/length to check the prefix information
• B. debug mpls ldp transport events to display events related to the LDP peer discovery mechanism
• C. show mpls forwarding labels <label-id> hardware egress location <node-id> to check the hardware label FIB
• D. show arp <prefix> location <node-id> for the next hop prefix
• E. show mpls ldp discovery for the corresponding label information
• F. debug mpls ea platform all to display MPLS setup events and errors

Answer: ACD

NEW QUESTION 15
A service provider runs MPLS in its core. What is the relationship between FIB, LIB, and LFIB in this
environment?

• A. Data from the FIB and LIB tables is used to generate the LFIB
• B. The FIB, LIB, and LFIB are populated independently
• C. The LIB and FIB are populated with labels and next-hop attributes in the control plane and are used topopulate the LFIB
• D. The LFIB is populated with information from the IP routing table and is shared with the FIB and LIB toassign labels to the path

Answer: A

NEW QUESTION 16
Which two characteristics describe the difference between MPLS QoS pipe and short-pipe models? (Choose two)

• A. Short-pipe mode does not need MPLS usage, but pipe mode does.
• B. In short-pipe mode, the egress LSR uses the tunneled PHB marking, but in pipe mode, the egress LSR uses the LSP PHB marking.
• C. Pipe mode does guarantee that the tunneled packet marking remains unchanged, but short-pipe does not.
• D. In short-pipe mode, the egress LSR uses the LSP PHB marking, but in pipe mode, the egress LSR uses the tunneled PHB marking.
• E. Short-pipe mode can be implemented on MPLS networks regardless of the MPLS PHP mechanism usage.

Answer: BE