NEW QUESTION 1
A VxRail D560 cluster was delivered six months ago and now needs to be prepared for installation with the target code. What is the correct method to complete the task?

• A. Boot into RASR ISO and perform a RASR Reset
• B. Boot into RASR USB and perform a RASR Reset
• C. Boot into SD card and perform a Factory Reset
• D. Boot into RASR ISO and perform a Factory Reset

Answer: A

NEW QUESTION 2
A VxRail Manager VM must be configured as follows:
* IP address: 192 168.10.16
* Net mask: 255.255.255.0
* Gateway: 192 168 10 254 Which command must be used?

• A. vxrail-network-config --ip 192 168 10.16-netmask 255.255.255.0-gateway 192 168 10.254
• B. vxrail-prrmary -config --ip 192 168 10 16 -netmask 255 255 255 0 -gateway 192 168 10 254
• C. vxrail-primary -config --vxrail-address 192.168.10 16 --vxrail-netmask 255 255 255 0 -vxrail-gateway 192.168,10 254
• D. vxrail-network -config --vxrail-address 192.166 10 16 --vxrail-netmask 255 255.255 0 --vxrail-gateway 192.168.10.254

Answer: C

NEW QUESTION 3
What is validated by running the Proactive VM Creation test in vCenter on a VxRail cluster?

• A. vSAN operates successfully
• B. Network firewalls are configured correctly
• C. vSAN has sufficient storage capacity
• D. Network performance is sufficient

Answer: D

NEW QUESTION 4
Which service determines the primary node after powering on the VxRail nodes during the deployment of a VxRail cluster?

• A. Loudmouth
• B. Election
• C. Marvin
• D. Mystic

Answer: C

NEW QUESTION 5
What is a valid 2-node VxRail cluster configuration?

• A. Series with 4x 25 GbE in a direct-connect configuration
• B. Series with 4x 10 GbE in a switch configuration
• C. Series with 4x 1 GbE in a direct-connect configuration
• D. Series with 2x 25 GbE in a switch configuration

Answer: B

NEW QUESTION 6
During the activation of Internal SRS, the implementation engineer receives a message that the deployment has failed What is a possible cause?

• A. SRS VE Gateway on the same subnet as the VxRail Manager
• B. VxRail status already set to installed' in IB database
• C. Site ID mismatch between the IB database and the SRS Wizard
• D. Witness Gateway not configured following Dell best practices

Answer: A

NEW QUESTION 7
An implementation engineer is tasked with setting up RecoverPoint for VMs on a single G Series chassis. How many VMs are licensed to be protected on the cluster?

• A. 5
• B. 10
• C. 15
• D. 20

Answer: C

NEW QUESTION 8
A planned VxRail Stretched Cluster will have four hybrid nodes at each site. What is the recommended storage policy to ensure cross-site and local protection, using storage as efficiently as possible?

• A. Site disaster tolerance – None keep data on Preferred (stretched cluster) Failures to tolerate – 1 failure – RAID-1 (Mirroring)
• B. Site disaster tolerance – Dual site mirroring (stretched cluster) Failures to tolerate – 1 failure – RAID-5 (Erasure Coding)
• C. Site disaster tolerance – Dual site mirroring (stretched cluster) Failures to tolerate – No data redundancy
• D. Site disaster tolerance – Dual site mirroring (stretched cluster)Failures to tolerate – 1 failure – RAID-1 (Mirroring)

Answer: B

NEW QUESTION 9
What is the minimum number of VxRail nodes required for a vSAN storage policy with RAID-6 (Erasure Coding)?

• A. 4
• B. 5
• C. 6
• D. 7

Answer: C

NEW QUESTION 10
Which two files are used to automate VxRail deployment and validate the network configuration?

• A. Appliance JSON file PEQ data file
• B. VxRail Configuration Portal PEQ data file
• C. VxRail Test Plan SPEQ
• D. Appliance JSON file SPEQ

Answer: A

NEW QUESTION 11
A VxRail API request has been executed and the user account does not have vCenter privileges to perform the task What code is returned?

• A. 200
• B. 207
• C. 403
• D. 500

Answer: D

NEW QUESTION 12
From what environment must a network administrator run VxRail network validation?

• A. Windows PowerShell command prompt
• B. Same subnet as VxRail Management Network
• C. Top of Rack switches
• D. VxRail Deployment Wizard

Answer: C

NEW QUESTION 13
What is a consideration when implementing a custom VDS on a VxRail cluster?

• A. Used by multiple clusters managed by a single vCenter instance
• B. Supported with external and internal vCenter Servers
• C. Supports only four NIC uplinks
• D. Supports only two NIC uplinks

Answer: B

NEW QUESTION 14
What is the recommended format for host names when using the VxRail Deployment Wizard for an External vCenter solution?

• A. FQDN for vCenter ServerHost name for VxRail Manager
• B. Host name for both vCenter Server and for VxRail Manager
• C. FQDN for both vCenter Server and for VxRail Manager
• D. Host name for vCenter Server FQDN for VxRail Manager

Answer: A

NEW QUESTION 15
Match each IDRAC Maintenance page tab to its description.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 16
What is a requirement for the vSAN Data-at-Rest Encryption?

• A. All-Flash or AII-NVMe VxRail
• B. VxRail with at least 3 nodes
• C. External Key Management Server
• D. External customer provided vCenter

Answer: C

NEW QUESTION 17
What is the maximum number of supported nodes in a VxRail Stretch Cluster?

• A. 16
• B. 30
• C. 32
• D. 64

Answer: B

NEW QUESTION 18
......