NSE7 Exam
Amazing nse7 exam To Try
Your success in Fortinet nse7 exam is our sole target and we develop all our fortinet nse7 braindumps in a way that facilitates the attainment of this target. Not only is our nse7 fortinet study material the best you can find, it is also the most detailed and the most updated. fortinet nse7 Practice Exams for Fortinet fortinet nse7 are written to the highest standards of technical accuracy.
Q11. What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.)
A. Reduce the session time to live.
B. Increase the TCP session timers.
C. Increase the FortiGuard cache time to live.
D. Reduce the maximum file size to inspect.
Answer: A,D
Q12. Examine the partial output from the IKE realtime debugshown in the exhibit; then answer the question below.
Why didn't the tunnel come up?
A. IKE mode configuration is not enabled in the remote IPsec gateway.
B. The remote gateway's Phase-2 configuration does not match the local gateway's phase-2configuration.
C. The remote gateway's Phase-1 configuration does not match the local gateway's phase-1 configuration.
D. One IPsec gateway is using main mode, while the other IPsec gateway is using aggressive mode.
Answer: B
Q13. Examine the output of the 'diagnose sys session list expectation' command shown in the exhibit; then answer the question below.
Which statement is true regarding the session in the exhibit?
A. it was created by the FortiGate kernel to allow push updates from FortiGuard.
B. it is for management traffic terminating at the FortiGate.
C. it is for traffic originated from the FortiGate.
D. it was created by a session helper or ALG.
Answer: A
Q14. Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN byenable the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output?
A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1
D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
Answer: A
Q15. When does a RADIUS server send anAccess-Challengepacket?
A. The server does not have the user credentials yet.
B. The server requires more information from the user,such as the token code for two-factor authentication.
C. The user credentials are wrong.
D. The user account is not found in the server.
Answer: B
Q16. An LDAP user cannot authenticate against a FortiGate device. Examine the real time debug output shown in the exhibit when the user attempted the authentication; then answer thequestion below.
Based on the output in the exhibit, what can cause this authentication problem?
A. User student is not found in the LDAP server.
B. User student is using a wrong password.
C. The FortiGate has been configured with the wrongpassword for the LDAP administrator.
D. The FortiGate has been configured with the wrong authentication schema.
Answer: A
Q17. Examine the following partial outputs from two routing debug commands; then answer the question below.
# get router info routing-table database
s 0.0.0.0/0 [20/0] via 10.200.2.254, port2, [10/0] s *> 0.0.0.0/0 [10/0] via 10.200.1.254, port1
# get router info routing-table all
s* 0.0.0.0/0 [10/0] via 10.200.1.254, port1
Why the default route using port2 is not displayed in the output of the second command?
A. it has a lower priority than the default route using port1.
B. it has a higher priority than the default route using portl.
C. it has a higher distance than the default route using portl.
D. it is disabled in the FortiGate configuration.
Answer: A
Q18. What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.)
A. Reduce the session time to live.
B. Increase the TCP session timers.
C. Increase the FortiGuard cache time to live.
D. Reduce the maximum file size to inspect.
Answer: A,D
Q19. Examine the following partial outputs from two routing debug commands; then answer the question below.
# get router info routing-table database
s 0.0.0.0/0 [20/0] via 10.200.2.254, port2, [10/0] s *> 0.0.0.0/0 [10/0] via 10.200.1.254, port1
# get router info routing-table all
s* 0.0.0.0/0 [10/0] via 10.200.1.254, port1
Why the default route using port2 is not displayed in the output of the second command?
A. it has a lower priority than the default route using port1.
B. it has a higher priority than the default route using portl.
C. it has a higher distance than the default route using portl.
D. it is disabled in the FortiGate configuration.
Answer: A
Q20. An administrator has enabled HA session synchronization in a HA cluster with two members. Which flag is added to a primary unit's session to indicate that it has been synchronized to the secondary unit?
A. redir
B. dirty
C. synced
D. nds
Answer: C