300-101 Exam
Where to find ccnp route 300 101 pdf
We provide real 300 101 route pdf exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco route 300 101 Exam quickly & easily. The ccnp route 300 101 dumps PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco ccnp 300 101 pdf dumps pdf and vce product and material, you can easily pass the 300 101 dumps exam.
P.S. Free 300-101 braindump are available on Google Drive, GET MORE: https://drive.google.com/open?id=1oF6hAYEiseB3LPIXYA2sgTXv0r2MX46d
New Cisco 300-101 Exam Dumps Collection (Question 12 - Question 21)
Q1. Refer to the exhibit.
After you apply this configuration to router R1, it fails to establish an eBGP neighbour relationship with R2. Which action do you take to correct the problem?
A. Configure the update-source for 10.1.1.2
B. Change the ebgp-multihop value to 1.
C. Add the no synchronization statement at the end of the configuration.
D. Replace the maximum-paths command at the end of the configuration with maximum- paths ibgp 4 import 2.
Answer: A
Q2. Refer to the exhibit.
A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up.
What did the TAC engineer configure incorrectly?
A. The crypto map is not configured correctly.
B. The crypto ACL is not configured correctly.
C. The crypto map is not applied to the correct interface.
D. The OSPF network is not configured correctly.
Answer: B
Q3. Scenario:
You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. The customer has disabled your access to the show running-config command.
Areas of Router 5 and 6 are not normal areas, inspect their routing tables and determine which statement is true?
A. R5's Loopback and R6's Loopback are both present in R5's Routing table
B. R5's Loopback and R6's Loopback are both present in R6's Routing table
C. Only R5's loopback is present in R5's Routing table
D. Only R6's loopback is present in R5's Routing table
E. Only R5's loopback is present in R6's Routing table
Answer: A
Topic 4, VPN Technologies
45.Refer to the following output:
Router#show ip nhrp detail
10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47 TypE. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
A. It was obtained directly from the next-hop server.
B. Data packets are process switches for this mapping entry.
C. NHRP mapping is for networks that are local to this router.
D. The mapping entry was created in response to an NHRP registration request.
E. The NHRP mapping entry cannot be overwritten.
Q4. What is the default maximum segment size for TCP traffic?
A. 536
B. 1492
C. 1500
D. 1508
E. 3340
F. 4096
Answer: A
Q5. Which traffic does the following configuration allow?
ipv6 access-list cisco
permit ipv6 host 2001:DB8:0:4::32 any eq ssh line vty 0 4
ipv6 access-class cisco in
A. all traffic to vty 0 4 from source 2001:DB8:0:4::32
B. only ssh traffic to vty 0 4 from source all
C. only ssh traffic to vty 0 4 from source 2001:DB8:0:4::32
D. all traffic to vty 0 4 from source all
Answer: C
Q6. Study this exhibit below carefully.
What is the effect of the distribute-list command in the R1 configuration?
A. R1 will permit only the 10.0.0.0/24 route in the R2 RIP updates
B. R1 will not filter any routes because there is no exact prefix match
C. R1 will filter the 10.1.0.0/24 and the 172.24.1.0/24 routes from the R2 RIP updates
D. R1 will filter only the 172.24.1.0/24 route from the R2 RIP updates
Answer: C
Explanation:
The command u201cdistribute-list 10 in Serial0 will create an incoming distribute list for interface serial 0 and refers to access list 10. So it will permit routing updates from 10.0.x.x network while other entries (in this case the 10.1.0.0/24 and 172.24.1.0/24 networks) will be filtered out from the routing update received on interface S0.
Q7. Refer to Exhibit.
A network engineer is unable to make VRF lite EIGRP adjacency work. There is nothing wrong with communication between R1 and R2. What command will eliminate the issue when executed on both routers?
A. (config-router-af)#autonomous-system 100
B. (config)#ip-multicast-routing
C. (config-vrf)#route-target both 100:1
D. config-router-af)#network 209.165.202.128.0.0.0.31
Answer: A
Q8. CORRECT TEXTJS Industries has expanded their business with the addition of their first remote office. The remote office router (R3) was previously configured and all corporate subnets were reachable from R3. JS Industries is interested in using route summarization along with the EIGRP Stub Routing feature to increase network stability while reducing the memory usage and bandwidth utilization to R3. Another network professional was tasked with implementing this solution. However, in the process of configuring EIGRP stub routing connectivity with the remote network devices off of R3 has been lost.
Currently EIGRP is configured on all routers R2, R3, and R4 in the network. Your task is to identify and resolve the cause of connectivity failure with the remote office router R3. Once the issue has been resolved you should complete the task by configuring route
summarization only to the remote office router R3.
You have corrected the fault when pings from R2 to the R3 LAN interface are successful, and the R3 IP routing table only contains 2 10.0.0.0 subnets.
Answer:
Here are the solution as below:
Explanation:
First we have to figure out why R3 and R4 can not communicate with each other. Use the show running-config command on router R3.
Notice that R3 is configured as a stub receive-only router. The receive-only keyword will restrict the router from sharing any of its routes with any other router in that EIGRP autonomous system. This keyword will also prevent any type of route from being sent. Therefore we will remove this command and replace it with the eigrp stub command: R3# configure terminal R3(config)# router eigrp 123 R3(config-router)# no eigrp stub receive-only R3(config-router)# eigrp stub
R3(config-router)# end
Now R3 will send updates containing its connected and summary routes to other routers. Notice that the eigrp stub command equals to the eigrp stub connected summary because the connected and summary options are enabled by default.
Next we will configure router R3 so that it has only 2 subnets of 10.0.0.0 network. Use the show ip route command on R3 to view its routing table:
Because we want the routing table of R3 only have 2 subnets so we have to summary sub- networks at the interface which is connected with R3, the s0/0 interface of R4.
There is one interesting thing about the output of the show ip route shown above: the 10.2.3.0/24, which is a directly connected network of R3. We canu2021t get rid of it in the routing table no matter what technique we use to summary the networks. Therefore, to make the routing table of R3 has only 2 subnets we have to summary other subnets into one subnet.
In the output if we donu2021t see the summary line (like 10.0.0.0/8 is a summaryu2026) then we should use the command ip summary-address eigrp 123 10.2.0.0 255.255.0.0 so that all the ping can work well.
In conclusion, we will use the ip summary-address eigrp 123 10.2.0.0 255.255.0.0 at the interface s0/0 of R4 to summary.
R4> enable R4# conf t
R4(config)# interface s0/0 R4(config-if)# ip summary-address eigrp 123 10.2.0.0 255.255.0.0
Now we jump back to R3 and use the show ip route command to verify the effect, the output is shown below:
Note: Please notice that the IP addresses and the subnet masks in your real exam might be different so you might use different ones to solve this question.
Just for your information, notice that if you use another network than 10.0.0.0/8 to summary, for example, if you use the command ip summary-address eigrp 123 10.2.0.0
255.255.0.0 you will leave a /16 network in the output of the show ip route command.
But in your real exam, if you donu2021t see the line "10.0.0.0/8 is a summary, Null0" then you can summarize using the network 10.2.0.0/16. This summarization is better because all the pings can work well.
Finally donu2021t forget to use the copy run start command on routers R3 and R4 to save the configurations.
R3(config-if)# end R3# copy run start R4(config-if)# end R4# copy run start
If the u201ccopy run startu201d command doesnu2021t work then use u201cwrite memory.u201d
Q9. Which encapsulation supports an interface that is configured for an EVN trunk?
A. 802.1Q
B. ISL
C. PPP
D. Frame Relay
E. MPLS
F. HDLC
Answer: A
Q10. Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network. Which of the following answers best describes the routeru2021s logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?
A. When the packet received on the LAN interface is permitted by the ACL listed on the tunnel gre acl command under the incoming interface
B. When routing the packet, matching a route whose outgoing interface is theGRE tunnel interface
C. When routing the packet, matching a route whose outgoing interface is the IPsec tunnel interface
D. When permitted by an ACL that was referenced in the associated crypto map
Answer: B
Explanation:
As for the correct answer, the process of routing a packet out a GRE tunnel interface triggers the GRE encapsulation action. As for the incorrect answers: There is no tunnel gre acl command. There is no IPsec tunnel interface. Finally, one answer refers to logic that would describe a routeru2021s logic when determining whether to encapsulate a packet into an IPsec tunnel.
P.S. Easily pass 300-101 Exam with Dumpscollection Free Dumps & pdf vce, Try Free: http://www.dumpscollection.net/dumps/300-101/ (436 New Questions)