300-101 Exam
Key benefits of ccnp route 300 101 pdf
Proper study guides for Refresh Cisco ROUTE Implementing Cisco IP Routing certified begins with Cisco 300 101 exam preparation products which designed to deliver the Actual route 300 101 questions by making you pass the ccnp route 300 101 pdf test at your first time. Try the free ccnp route 300 101 demo right now.
P.S. Actual 300-101 prep are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g3xBE0KhVLL-l1SXbBZMbJhQ4SK2THNQ
New Cisco 300-101 Exam Dumps Collection (Question 4 - Question 13)
Question No: 4
Your company uses Voice over IP (VoIP). The system sends UDP datagrams containing the voice data between communicating hosts. When areas of the network become busy, some
of the datagrams arrive at their destination out of order. What happens when this occurs?
A. UDP will send an ICMP Information request message to the source host.
B. UDP will pass the information in the datagrams up to the next OSI layer in the order in which they arrive.
C. UDP will drop the datagrams that arrive out of order.
D. UDP will use the sequence numbers in the datagram headers to reassemble the data into the
Answer: B
Question No: 5
Your Company trainee asks you, in the context of IPv6 and OSPF, what best describes a type 9 LSA? What should you tell her?
A. Link LSA
B. Interarea prefix LSA for ABRs
C. Router LSA
D. Switch LSA
E. Intra-area prefix LSA
F. None of the above
Answer: E
Question No: 6
Refer to the exhibit. The DHCP client is unable to receive a DHCP address from the DHCP server. Consider the following output:
hostname RouterB
!
interface fastethernet 0/0
ip address 172.31.1.1 255.255.255.0
interface serial 0/0
ip address 10.1.1.1 255.255.255.252
!
ip route 172.16.1.0 255.255.255.0 10.1.1.2
Which configuration is required on the Router B fastethernet 0/0 port in order to allow the DHCP client to successfully receive an IP address from the DHCP server?
A. RouterB(config-if)# ip helper-address 172.16.1.2
B. RouterB(config-if)# ip helper-address 172.16.1.1
C. RouterB(config-if)# ip helper-address 172.31.1.1
D. RouterB(config-if)# ip helper-address 255.255.255.255
Answer: A
Question No: 7
Which three options are valid DHCPv6 functions? (Choose three.)
A. Server
B. client
C. approver
D. requester
E. requester
F. ACK
G. relay
Answer: A,B,G
Question No: 8
A network engineer has configured a tracking object to monitor the reachability of IP SLA 1. In order to update the next hop for the interesting traffic, which feature must be used in conjunction with the newly created tracking object to manipulate the traffic flow as required?
A. SNMP
B. PBR
C. IP SLA
D. SAA
E. ACLs
F. IGP
Answer: B
Question No: 9
Refer to the exhibit.
A network engineer is troubleshooting a DMVPN setup between the hub and the spoke. The engineer executes the command show crypto isakmp sa and observes the output that is displayed. What is the problem?
A. That ISAKMP is not enabled
B. That ISAKMP is using default settings
C. An incompatible IP sec transform set
D. An incompatible ISAKMP policy
Answer: B
Question No: 10
A network administrator creates a static route that points directly to a multiaccess interface, instead of the next-hop IP address. The administrator notices that Cisco Express Forwarding ARP requests are being sent to all destinations. Which issue might this configuration create?
A. Low bandwidth usage
B. High memory usage
C. Cisco Express Forwarding routing loop
D. High bandwidth usage
E. IP route interference
Answer: C
Question No: 11
Refer to the exhibit.
Which option prevents routing updates from being sent to the access layer switches?
A. DWS1(config-router)# passive-interface default DWS2(config-router)# passive-interface default
B. ALS1(config-router)# passive-interface default ALS2(config-router)# passive-interface default
C. DWS1(config-router)# passive-interface gi1/1 DWS1(config-router)# passive-interface gi1/2 DWS2(config-router)# passive-interface gi1/1 DWS2(config-router)# passive-interface gi1/2
D. ALS1(config-router)# passive-interface gi0/1 ALS1(config-router)# passive-interface gi0/2 ALS2(config-router)# passive-interface gi0/1 ALS2(config-router)# passive-interface gi0/2
Answer: C
Question No: 12
What are the default timers for RIPng?
A. Update: 30 seconds Expire: 180 seconds Flush: 240 seconds
B. Update: 20 seconds Expire: 120 seconds Flush: 160 seconds
C. Update: 10 seconds Expire: 60 seconds Flush: 80 seconds
D. Update: 5 seconds Expire: 30 seconds Flush: 40 seconds
Answer: A
Question No: 13
Two aspects of an IP SLA operation can be tracked: state and reachability. Which statement about state tracking is true?
A. When tracking state, an OK return code means that the track's state is up; any other return code means that the track's state is down.
B. When tracking state, an OK or over threshold return code means that the track's state is up; any other return code means that the track's state is down.
C. When tracking state, an OK return code means that the track's state is down; any other return code means that the track's state is up.
D. When tracking state, an OK or over threshold return code means that the track's state is down; any other return code means that the track's state is up.
Answer: A
100% Refresh Cisco 300-101 Questions & Answers shared by 2passeasy, Get HERE: https://www.2passeasy.com/dumps/300-101/ (New 487 Q&As)