300-101 Exam
What tells you about 9tut ccnp 300 101
Your success in Cisco ccnp route 300 101 dumps pdf is our sole target and we develop all our ccnp 300 101 braindumps in a way that facilitates the attainment of this target. Not only is our 300 101 vce study material the best you can find, it is also the most detailed and the most updated. ccnp 300 101 dumps Practice Exams for Cisco CCDP ccnp route 300 101 pdf are written to the highest standards of technical accuracy.
P.S. Simulation 300-101 Q&A are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g4kPItyKIZuA3JfCSZX112aKL18D2zfl
New Cisco 300-101 Exam Dumps Collection (Question 8 - Question 17)
Q8. Refer to the exhibit. Which interoperability technique implemented on the dual-stack routers would allow connectivity between IPv6 sites across automatic created tunnels using the 2002::/16 prefix?
A. Dual Stack
B. NAT-PT
C. 6to4 tunnel
D. GRE tunnel
E. ISATAP tunnel
Answer: C
Q9. Whatu2021s uRPF checking first when the packet enters the interface ? or when unicast reverse patch forwarding is configured on interinterface.
A. it check the ingress access list
B. it check the egress access list
C. Route available in FIB ot it verifies a reverse patch via the fib to the source
D. it verify that the source has a
Answer: C
Q10. An administrator needs to setup an NTP client to provide updates to local without synchronizing to server. What is the command?
A. Serve
B. Serve-only
C. peer
Answer: A
Q11. What does the show ip route vrf CISCO command display?
A. directly connected routes for VRF CISCO.
B. the routing table for VRF CISCO.
C. the global routing table.
D. all routing tables that start with VRF CISCO.
E. the route distinguisher for VRF CISCO
Answer: B
Q12. Which two protocols can be affected by MPP? (Choose two)
A. POP
B. SMTP
C. HTTP
D. SFTP
E. SSH
Answer: C,E
Explanation: Following are the management protocols that the MPP feature supports. These management protocols are also the only protocols affected when MPP is enabled.
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifBlocks Extensible Exchange Protocol (BEEP)
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifFTP
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifHTTP
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifHTTPS
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifSSH, v1 and v2
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifSNMP, all versions
u2022http://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifTelnet
u2022http://www.cisc:.com-/c/dom/en/us/td/i/templates/blank.gifTFTP http://www.cisco.com/c/en/us/td/docs/ios/12_4t/12_4t11/htsecmpp.html
Q13. Which two statements about NTP stratum are true? (Choose two )
A. Stratum 15 indicates a device that is not synchronized
B. Stratum 1 devices receive their time from a peer that is connected directly to an authoritative time source.
C. The highest stratum level a synchronized device can have is 16.
D. Stratum 2 devices receive their time from a peer that is connected directly to an authoritative time source
E. Stratum 0 devices are connected directly to an authoritative time source
F. Stratum 1 devices are connected directly to an authoritative time source
Answer: A,F
Q14. Refer to the exhibit.
How would you confirm on R1 that load balancing is actually occurring on the default- network (0.0.0.0)?
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping along with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
Answer: D
Explanation:
The most simple method to test load balancing is to use the u201ctracerouteu201d command. If load balancing is working correctly, we will see different paths to reach the destination each time
we use that command.
Unknown address will be routed via the default-network 0.0.0.0 so we must use an address that is not explicitly in the routing table.
Q15. What is the IPv6 address FF02::2 used for?
A. all hosts in a local segment
B. all routers in a local segment
C. all hosts in a particular multicast group
D. all routers in an autonomous system
Answer: B
Explanation:
To identify all nodes for the node-local and link-local scopes, the following multicast addresses are defined:
u2022 FF01::1 (node-local scope all-nodes address)
u2022 FF02::1 (link-local scope all-nodes address)
To identify all routers for the node-local, link-local, and site-local scopes, the following multicast addresses are defined:
u2022 FF01::2 (node-local scope all-routers address)
u2022 FF02::2 (link-local scope all-routers address)
u2022 FF05::2 (site-local scope all-routers address)
Q16. Which two statements about IP access-lists are true? (Choose two)
A. IP access-lists without at least one deny statement permit all traffic by default.
B. Extended access-lists must include port numbers.
C. They support wildcard masks to limit the address bits to which entries are applies.
D. Entries are applied to traffic in the order in which they appear.
E. They end with an implicit permit.
Answer: C,D
Q17. Which technology uses the many-to-one method of mapping IP addresses?
A. static NAT
B. dynamic NAT
C. NAT-PT
D. PAT
Answer: D
Explanation: Overloadingu2014Maps multiple unregistered IP addresses to a single registered IP address (many to one) using different ports. This method is also known as Port Address Translation (PAT). By using overloading, thousands of users can be connected to the Internet by using only one real global IP address
100% Renew Cisco 300-101 Questions & Answers shared by Thedumpscentre, Get HERE: http://www.thedumpscentre.com/300-101-dumps/ (New 487 Q&As)