400-101 Exam
Foolproof cisco 400 101 tips
Testking offers free demo for ccie 400 101 exam. "CCIE Routing and Switching (v5.0)", also known as cisco 400 101 exam, is a Cisco Certification. This set of posts, Passing the Cisco ccie 400 101 exam, will help you answer those questions. The 400 101 ccie Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco cisco 400 101 exams and revised by experts!
P.S. Free 400-101 preparation exams are available on Google Drive, GET MORE: https://drive.google.com/open?id=1NSUhfDNX5MaN4i2EjLlDDw6kSsXs6DwU
New Cisco 400-101 Exam Dumps Collection (Question 6 - Question 15)
Q1. On an MPLS L3VPN, which two tasks are performed by the PE router? (Choose two.)
A. It exchanges VPNv4 routes with other PE routers.
B. It typically exchanges iBGP routing updates with the CE device.
C. It distributes labels and forwards labeled packets.
D. It exchanges VPNv4 routes with CE devices.
E. It forwards labeled packets between CE devices.
Answer: A,C
Q2. Which two items must be confined to caputure packet data with the Embedded Packet Caputure feature ? (Choose two)
A. the capture point
B. the capture buffer
C. the coputure file export location
D. the caputure filter
E. the capture rate
F. the buffer memory size
Answer: A,B
Q3. Which two statement about the EIGRP Over the Top feature are true?(Choose two.)
A. EIGRP routers traffic between the PE devices.
B. Traffic is USP-encapsulated on the control plane.
C. The neighbor command must be configured with LISP encapsulation on wach CE device.
D. The network statement must be configured on each PE device to connect separate EIGRP sites.
E. The network statement must be configured on each CE device to connect separate EIGRP sites
F. Traffic is LISP-encapsulated on the data plane.
Answer: C,F
Q4. Which command can you enter to disable logging for terminal lines?
A. no logging trop
B. no logging monitor
C. no logging buffer
D. no logging console
E. no logging count
Answer: B
Q5. What command can you enter on a Cisco router so that it can both polled a time server and be polled by a time server
A. ntp server
B. ntp broadcast client
C. ntp broadcast destination
D. ntp peer
Answer: D
Q6. Which options is the default LACP load-balancing algorithm for IP traffic on Layer 3?
A. the source and destinnation IP port
B. the destination IP port
C. the source and destination IP address
D. the destination port
E. the source IP port
Answer: C
Q7. Refer to the exhibit.
If router R1 sends traffic marked with IP precedence 3 to R2's Loopback 0 address, which class would the traffic match on R2's Gi1/0 interface?
A. CM-CLASS-3
B. class-default
C. CM-CLASS-2
D. CM-CLASS-1
Answer: B
Q8. ON NO: 402
Refer to the exhibit.
Which two statements about the output are true? (Choose two.)
A. 802.1D spanning tree is being used.
B. Setting the priority of this switch to 0 for VLAN 1 would cause it to become the new root.
C. The hello, max-age, and forward delay timers are not set to their default values.
D. Spanning-tree PortFast is enabled on GigabitEthernet1/1.
Answer: A,B
Explanation:
802.1D is the standard for Spanning tree, which is being used here. For priority, The priority order starts from 0 (yes, 0 is valiD. and then increases in 4096.
0, 4096, 8192, 12288, u2026. Etc.
The lower the number is, the higher is the priority. Here we see that the current root has a priority of 8192, so configuring this with a priority of 0 will make it the new root.
Q9. Refer to the exhibit ,
while Reviewing a log file on a router with this NTP configuration ,you note that the log entries of the router display a different time than the NTP timE.which action can u take to correct the problem?
A. add the local time keyword to the service timestamps log datetime statement.
B. add the msec keyword to the service time stamps log datetime statement
C. add the statement ntp broadcast to the ntp configuration of the neighboring router
D. configure the router to be the NTP master
E. Remove the datetime keyword from the service time stamps log datetime statement.
Answer: A
Q10. Which Catalyst switch feature configured on a per-port basis can be used to prevent attached hosts from joining select multicast group?
A. IGMP Filtering
B. MLD Filtering
C. IGMP Snooping
D. PIM Snooping
Answer: A
Recommend!! Get the Free 400-101 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/400-101/ (New 911 Q&As Version)